Items where Division is "Faculty of Engineering > Department of Mechanical Engineering" and Year is 2014

Up a level
Export as [feed] Atom [feed] RSS 1.0 [feed] RSS 2.0
Group by: Creators | Item Type | No Grouping
Jump to: B | K | M | Y
Number of items: 14.

B

Bakar, Abu (2014) Bahan Ajar Mekatronika. Unimal Press, Lhokseumawe.

K

Kam, T. Y. and Nayan, A. (2014) Vibro-acoustic analysis of orthotropic sound radiating plate using a simple firstorder shear deformation theory. In: 31th National Conference on Mechanical Engineering of CSME, December 6th and 7th 2014, Feng Chia University in TaiChung County, Taiwan.

M

Muhammad, Muhammad and Putra, Reza (2014) Bahan Ajar Bahan Teknik. Unimal Press, Lhokseumawe.

Y

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: JURNAL ILMIAH “Chip Formation and Surface Roughness in Dry Machining of Aluminium Alloys”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: JURNAL ILMIAH “Effect of Machining Process on Surface Microhardness of Titanium Carbide Reinforced Aluminium LM6 Composite”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: JURNAL ILMIAH “Experimental Investigation on Surface Roughness and Tool Wear in Dry Machining of TiC Reinforced Aluminium LM6 Composite”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: JURNAL ILMIAH “Influence of Cutting Parameters on Surface Roughness for Wet and Dry Turning Process”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: JURNAL ILMIAH “Optimization of Cutting Parameters on Turning Process Based on Surface Roughness using Response Surface Methodology”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: JURNAL ILMIAH “Surface Quality and Chip Formation in Turning of LM6 Aluminium Alloy and Particulate Reinforced Metal Matrix Composite”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: PROSIDING ILMIAH “Development of Tool Database Management System for Laboratory”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad (2014) HASIL PENILAIAN SEJAWAT SEBIDANG ATAU PEER REVIEW KARYA ILMIAH: PROSIDING ILMIAH “Optimisation of Machining Parameters using Design of Experiment”. Universitas Malikussaleh. (Unpublished)

Yusuf, Muhammad and Arifin, M.K.A and Sulaiman, S and Ismail, N. (2014) Effect of Machining Process on Surface Microhardness of Titanium Carbide Reinforced Aluminium LM6 Composite. Applied Mechanics and Materials, 564. pp. 495-500. ISSN 16627482

Yusuf, Muhammad and Arifin, M.K.A and Sulaiman, S and Ismail, N. (2014) Experimental Investigation on Surface Roughness and Tool Wear in Dry Machining of TiC Reinforced Aluminium LM6 Composite. Materials Science Forum, 773-77. pp. 339-347. ISSN 02555476

Yusuf, Muhammad and Arifin, M.K.A and Sulaiman, S and Ismail, N. (2014) Surface Quality and Chip Formation in Turning of LM6 Aluminium Alloy and Particulate Reinforced Metal Matrix Composite. Materials Science Forum, 773-77. pp. 894-901. ISSN 02555476

This list was generated on Mon Dec 2 18:40:09 2024 WIB.